<div dir="ltr"><div class="gmail_default" style="font-size:small"><br clear="all"></div><div><div class="gmail_signature" data-smartmail="gmail_signature"><div dir="ltr"><div><div dir="ltr"><div><div dir="ltr"><div><div dir="ltr"><br>- Matthew<div style="font-size:small;display:inline" class="gmail_default">​ nj4y​</div><br></div></div></div></div></div></div></div></div></div>
<br><div class="gmail_quote">---------- Forwarded message ----------<br>From: <b class="gmail_sendername">Paul Stoetzer</b> <span dir="ltr"><<a href="mailto:n8hm@arrl.net">n8hm@arrl.net</a>></span><br>Date: Fri, Nov 3, 2017 at 7:53 PM<br>Subject: [amsat-bb] Getting Ready for RadFxSat (Fox-1B)<br>To: "<a href="mailto:amsat-bb@amsat.org">amsat-bb@amsat.org</a>" <<a href="mailto:amsat-bb@amsat.org">amsat-bb@amsat.org</a>><br><br><br>INTRODUCTION<br>
<br>
RadFxSat (Fox-1B) is scheduled for launch on November 10, 2017.<br>
RadFxSat is one of four CubeSats making up the NASA ELaNa XIV mission,<br>
riding as secondary payloads aboard the Joint Polar Satellite System<br>
(JPSS)-1 mission. JPSS-1 will launch on a Delta II from Vandenberg Air<br>
Force Base, California.<br>
<br>
RadFxSat is a partnership with Vanderbilt University ISDE and hosts<br>
four payloads for the study of radiation effects on commercial off the<br>
shelf components. RadFxSat features the Fox-1 style FM U/v repeater<br>
with an uplink on 435.250 MHz (67.0 Hz CTCSS) and a downlink on<br>
145.960 MHz. Satellite and experiment telemetry will be downlinked via<br>
the “DUV” subaudible telemetry stream and can be decoded with the<br>
FoxTelem software<br>
(<a href="https://www.amsat.org/foxtelem-software-for-windows-mac-linux/" rel="noreferrer" target="_blank">https://www.amsat.org/<wbr>foxtelem-software-for-windows-<wbr>mac-linux/</a>).<br>
<br>
<br>
LAUNCH AND EARLY ORBIT PHASE (LEOP)<br>
<br>
RadFxSat will launch at 01:47 PST (09:47 UTC) on November 10, 2017<br>
from Vandenberg Air Force Base, California. At this time, pre-launch<br>
Keplerian elements are not expected to be available. However, based on<br>
the Local Time of the Ascending Node (LTAN) of the primary payload,<br>
13:30, stations should expect to have their initial ascending passes<br>
starting around noon local time. The estimated time of “First<br>
Veronica,” the initial beacon after deployment, is 12:07 UTC. Due to<br>
the tight constraints on the primary payload deployment, the secondary<br>
payloads may be delayed slightly, so this should be considered the<br>
soonest the transmitter will be enabled. Orbital elements will be<br>
published as soon as they are available on the AMSAT website. Stations<br>
in Europe, South America, and North America should point your beams<br>
south and have FoxTelem running while awaiting the initial post-launch<br>
Keplerian elements.<br>
<br>
Participation in telemetry collection by as many stations in as many<br>
parts of the world as possible is essential as AMSAT Engineering looks<br>
for successful startup and indications of the general health and<br>
function of the satellite as it begins to acclimate to space.<br>
<br>
If you are capturing telemetry with FoxTelem please be sure that<br>
"Upload to Server" is checked in your settings, and that your “Ground<br>
Station Params” are filled in as well. You can help AMSAT and everyone<br>
waiting to get on the air with RadFxSat tremendously by capturing<br>
RadFxSat telemetry.<br>
<br>
About 60 minutes after deployment, or 140 minutes after launch, the<br>
satellite will start up in Beacon Mode. In this initial mode, the<br>
transmitter is limited to 10 seconds on time and then will be off for<br>
two minutes. For those of you capturing telemetry, that means that you<br>
will only see Current frames and no High or Low frames. The High and<br>
Low frames are truncated as it takes just over the 10 second limit to<br>
send two frames. Veronica may also be cut off before she gets to say<br>
her whole ID string as the full ID, “RadFxSat Fox-1B Safe Mode,” is a<br>
bit longer than the approximately 3.5 seconds she has in Beacon Mode.<br>
If the voice ID is cut off, the satellite is still in Beacon Mode.<br>
<br>
If AMSAT Engineering is seeing nominal values from the telemetry you<br>
gather, the satellite will be commanded from Beacon Mode to Safe Mode<br>
on the first good pass over the United States. In Safe Mode, the<br>
satellite transmits a full two frames of telemetry (one Current frame<br>
followed by, and alternating each ID cycle, a High or a Low frame).<br>
Veronica now has time to make the whole ID announcement in Safe Mode.<br>
<br>
The on-orbit checkout procedure for RadFxSat is similar to<br>
Fox-1A/AO-85 and could be completed in as little as a few days if<br>
users cooperate. It is very important, and good amateur operating<br>
practice, to refrain from using the transponder uplink so the on-orbit<br>
tests can be performed, including when the satellite is switched into<br>
Transponder Mode for testing.<br>
<br>
AMSAT will make it broadly known when the tests are complete and the<br>
transponder is available for all to use. If you hear someone on the<br>
transponder, please do not assume that it is open for general use -<br>
check AMSAT’s website, Facebook, and Twitter before transmitting to be<br>
sure you do not interfere with testing.<br>
<br>
AMSAT asks all satellite operators to contribute just a little bit of<br>
your time by gathering telemetry, not using the transponder uplink, to<br>
help complete the last few days of getting RadFxSat operating for the<br>
amateur radio community.<br>
<br>
Lots of hams put thousands of volunteer hours of their time into<br>
making RadFxSat happen. Just like any ham radio project you might<br>
undertake, AMSAT builds satellites. AMSAT volunteers do it because<br>
they like to, and when they are done, AMSAT freely shares their<br>
project with hams everywhere as is the spirit of amateur radio.<br>
<br>
Thank you very much and see you on the bird!<br>
<br>
<br>
RADIO PROGRAMMING CHART<br>
<br>
RadFxSat (Fox-1B) Doppler Shift Correction<br>
<br>
Memory 1 (AOS) - Transmit 435.240 MHz (67.0 Hz Tone), Receive 145.960 MHz<br>
Memory 2 (Approaching) - Transmit 435.245 MHz (67.0 Hz Tone), Receive<br>
145.960 MHz<br>
Memory 3 (TCA) - Transmit 435.250 MHz (67.0 Hz Tone), Receive 145.960 MHz<br>
Memory 4 (Departing) - Transmit 435.255 MHz (67.0 Hz Tone), Receive 145.960 MHz<br>
Memory 5 (LOS) - Transmit 435.260 MHz (67.0 Hz Tone), Receive 145.960 MHz<br>
<br>
Frequencies are subject to change post-launch.<br>
<br>
<br>
SPECIAL MEMBERSHIP OFFER<br>
<br>
As part of the preparations for the launch of RadFxSat, AMSAT is<br>
making the “Getting Started With Amateur Satellites” book available<br>
for a limited time as a download with any paid new or renewal<br>
membership purchased via the AMSAT Store. This offer is only available<br>
with purchases completed online, and for only a limited time. A<br>
perennial favorite, Getting Started is updated every year with the<br>
latest amateur satellite information, and is the premier primer of<br>
satellite operation. The 182 page book is presented in PDF format, in<br>
full color, and covers all aspects of making your first contacts on a<br>
ham radio satellite.<br>
<br>
Please take advantage of this offer today by visiting the AMSAT store<br>
at <a href="https://www.amsat.org/shop/" rel="noreferrer" target="_blank">https://www.amsat.org/shop/</a> and selecting any membership option.<br>
While there, check out AMSAT’s other items, including the M2 LEOpack<br>
antenna system, Arrow antennas, AMSAT shirts, and other swag. Be sure<br>
to view your cart before going to checkout. If you add a membership<br>
and then go directly to checkout, you’ll never see an option to add<br>
your free gift.<br>
______________________________<wbr>_________________<br>
Sent via <a href="mailto:AMSAT-BB@amsat.org">AMSAT-BB@amsat.org</a>. AMSAT-NA makes this open forum available<br>
to all interested persons worldwide without requiring membership. Opinions expressed<br>
are solely those of the author, and do not reflect the official views of AMSAT-NA.<br>
Not an AMSAT-NA member? Join now to support the amateur satellite program!<br>
Subscription settings: <a href="http://www.amsat.org/mailman/listinfo/amsat-bb" rel="noreferrer" target="_blank">http://www.amsat.org/mailman/<wbr>listinfo/amsat-bb</a><br>
</div><br></div>